Digital TV Audio Processor. 5 Band processing. Dinamic and Loudness control. Powerful AGC. Perfect “Lip-Sync”. Analog, AesEbu e SDI IN/OUT.
GENERAL
- Dimension: 1 rack unit, 352 x 483 x 44 mm
- ~ AC Rate: 230 Vac 50 Hz / 115 Vac 60 Hz ±10%
- Type of power supply: Transformer- based
- Processing architecture: Fully Digital based on DSP 24bit/100Mhz.
- Operating temp. range: - 5 to + 50 °C
AUDIO PROCESSOR
SYSTEM PERFORMANCE
- Frequency Response: 30 Hz - 15 KHz (-0.1 dB) - Analog Processing Chain
- Sample Rate: Depending on processing being performed, from 47.5 to 760 KHz
- Total System Distortion: 0.008% - (0.005% at 1 KHz)
- Output Noise: The Falcon five Tv / five Tv Elite’s noise floor, in bypass mode, is primarily governed by the dynamic range of CS8420 digital rate converter, which has a specified Dynamic Range of 126 dB
- Stereo CrossTalk: >-80 dB (from 30 Hz to 15 KHz)
PROCESS ARCHITECTURE
- Min. Processing Delay: as low as technically possible: max 4 msec for all processing curves
- Number of Presets: 10 Factory Presets + 10 User Presets
- Preset Memory type: Non volatile memory, factory presets protected against accidental deletion
- Preset Import / Export: import / export from and to a file, either in groups or individually
- Wizard procedure controls: Density, Compression, Equalization, Expansion
5-BAND PROCESS
- Falcon five Tv Elite Audio: Agc Drive, Agc Attack, Agc Gate Thr,
- Preprocess: Stereo Enhancer, Pre-Process Equalizer, Speech Detector
- Falcon five Tv Audio: Agc Drive, Agc Attack, Agc Gate Thr,
- Preprocess: Speech Detector
- Falcon five TV Elite Audio: Band1, Band2, Band3, Band4, Band5
- Process: compressor, Process Mode, Band Coupling, Density, Brillance, SuperBass
- Falcon five Tv Audio: Band1, Band2, Band3, Band4, Band5
- Process: compressor, Process Mode (without lookahead), Density, Brillance
SOUND ENHANCING
- Stereo Enhancer: Band, Depth, Fx Lim & Drive
- Super Bass: On/Off, Bass Type & Drive
- Brilliance: On/Off & Level
- Speech Detector: Automatic, 9 operating modes
INPUT & OUTPUT
ANALOG AUDIO INPUT
- Connectors: Two EMI-suppressed XLR female.
- Input impedance: 600 / 10K / 50 K ohms electronically balanced, jumper selectable
- Input Configuration: Stereo / Mono / L+R / Mono R / Mono L. Flat, 50 mcrosec or 75 microsec pre-emphasis sel.
- Nominal Input Level (sensitivity): adjustable from -10.0 dBu to 12.0 dBu; +24 dBu max
- Input Signal-to-Noise: 108 dB (A weighted)
DIGITAL AUDIO INPUT
- Connector Type: XLR female. XLR transformer balanced & floating. 110 Ohm impedance
- Input Configuration: Stereo / Mono L+R / Mono R / Mono L. Flat, 50 or 75 microsec pre-emphasis
- Formats: AES3/EBU
- Input Rates: 32/44.1/48/64/88.2/96 KHz with automatic selection and jitter correction, 16/20/24 bit res.
- Nominal Level adj (sensitivity): From 0.0 dBFs to -25 dBFs (0.1 dBu step)
- Dynamic Range: 125 dB (Typ), 122 dB (Min)
ANALOG AUDIO OUTPUT
- Connectors: Two, EMI-suppressed XLR-male. Balanced or unbalanced. 600 Ohm
- Configuration: Stereo. Flat or pre-emphasized (50 or 75 microsec). +-3 microsec pre-emphasis correction
- Output Level: (100% peak mod.): adj -6 dBu to + 20 dBu peak, into 600 Ohms load, 120% Peak Mod. allowed
- Stereo CrossTalk: >-70 dB, 20 Hz - 15 Hz
- Signal-To-Noise: >100 dB (A Weighted) - >97 dB (unweighted), 20 Hz - 15 Hz
- Distortion: 0.005% THD, 20 Hz - 15 Hz
- Hardware bypass: Internal relays connect to respective analog audio input in the event AC Power drops
DIGITAL AUDIO OUTPUT
- Connector Type: XLR male 110 Ohm impedance
- Formats / Configuration: AES3/EBU, flat or pre-emphasized (50 or 75 usec)
- Sample Rates: 32/44.1/48/64/88.2/96 KHz internal or synchr. to audio input. 16/20/24 bit
- Output Level: From 0.0 dBFs to -25.0 dBFs (0.1 dBFs Step)
INPUT CHANGEOVER
- Inputs: Stereo analog audio, AES / EBU audio
- Fail mode: Lack of analog or AES/EBU audio
- Fail Time: From 1 to 120 seconds
- Restore Time: 1 sec to 250 sec (user settable)
- Digital SDI: 2x BNC
COMMUNICATION
I/O COMMUNICATION
- Serial Ports: 3 x RS232 optoinsulated or 2 x RS232 + 1 x RS485 (option). 2400 - 38400 Baud. Se rial Port 1 & 2 support dial-up modem.
- Ethernet: 10/100 BaseT Ethernet on RJ45 connector
- Supported Protocols: SNMP, UECP, TCP/IP, NTP
- Communication tools: Web Server, dedicated Pc Control Software, textual Configuration Editor
- Front panel displays: Double Graphic display 160x32
GPI/O INTERFACE
-Inputs: 4, optocoupled, floating
- Outputs: 4 Relays
- Connector: 1 x SubD 25 pin female
